Geekcreit® DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver
42
Direct purchase from the factory 
Tabbacin Biyan Kuɗi lafiya
Kyauta Kyauta
Manufar Jigilar Kaya
Manufar KomawaKyauta Kyauta
Barka da zuwa Roymall, shafinku na siyan kyaututtuka masu inganci. Muna girmama goyon bayanku, kuma muna ba da kyauta kyauta tare da kowane siyayya. Shirya don bincika tarinmu kuma ku sami kyaututtukanku masu dacewa.Manufar Jigilar Kaya
Za mu aika kayanku cikin kwanaki 2 bayan siyayya.Lokacin jigilar kaya yawanci kwanaki 5-7 ne.Saboda jigilar mu ta duniya ne, lokacin jigilar zai dogara da wurin ku.1. Manufar Komawa
Muna karɓar abubuwan da aka saya daga roymall.com kawai. Ba za a iya mayar da kyauta kyauta ba. Dole ne abu ya kasance ba a yi amfani da shi ba kuma a cikin yanayin da kuka karɓa.Za mu sarrafa komawar ku cikin kwanaki 3-5 bayan karɓa.Ba za a iya mayar da abubuwan da aka keɓance ba.Tuntuɓi mu. service@roymall.com ko Whatsapp: +86193598494712.Manufar Maida Kuɗi
Za ku sami cikakken maida kuɗi bayan mu karɓi abubuwan da aka dawo. Kuɗin jigilar kaya ba za a iya mayar da su ba.Tuntuɓi mu. service@roymall.com ko Whatsapp: +8619359849471
>>>Click here to buy the remote control<<<
n
nSpecification:
n
n1. Input Voltage: DC10-14V
n2. Standby Current: <5MA
n3. RF Frequency: 433MHZ
n4. RF Working mode:Super heterodyne receiver
n5. Receiver Sensitivity: >90dBm
n6. Remote Control Distance: >100 meter(In open environment)
n7. Decoding Way: MCU Software decoding
n8. Can store the number of remote control:50
n9. Support remote control type: Fixed code, learning code
n10. Channel: 1CH
n11. Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
n12. Wiring Method:Fixed wiring terminal
n13. Working Voltage: DC12V
n14. Output Current: 10A
n15. Rated load:10A 250VAC / 10A 125VAC, 10A 30VDC / 10A 28VDC
n16. Output:Normally open,Common,Normally closed
n17. Dimension:3.5cm*3cm*1.6cm
n
nWorking/output way:
n
n1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
n2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
n3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
n4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
n
nDescription:
n
n1. Press the learning code .the indicator flash ,loosen your finger ,press any button of the remote control
nthe indicator flash 2 times and off .it mean you learn it successfully .
n2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless 433MHz remote control
n3. Remove/clean :press the learning button about 8 seconds , the indicator turn on to off, it means the information that you keep have been removed successfully .
n
nPackage included:
n
n1/2/3/5/10/20 x 12V 1CH 433MHz Wireless Relay Switch Receiver (optional)
n
nSpecification:
n
n1. Input Voltage: DC10-14V
n2. Standby Current: <5MA
n3. RF Frequency: 433MHZ
n4. RF Working mode:Super heterodyne receiver
n5. Receiver Sensitivity: >90dBm
n6. Remote Control Distance: >100 meter(In open environment)
n7. Decoding Way: MCU Software decoding
n8. Can store the number of remote control:50
n9. Support remote control type: Fixed code, learning code
n10. Channel: 1CH
n11. Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
n12. Wiring Method:Fixed wiring terminal
n13. Working Voltage: DC12V
n14. Output Current: 10A
n15. Rated load:10A 250VAC / 10A 125VAC, 10A 30VDC / 10A 28VDC
n16. Output:Normally open,Common,Normally closed
n17. Dimension:3.5cm*3cm*1.6cm
n
nWorking/output way:
n
n1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
n2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
n3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
n4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
n
nDescription:
n
n1. Press the learning code .the indicator flash ,loosen your finger ,press any button of the remote control
nthe indicator flash 2 times and off .it mean you learn it successfully .
n2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless 433MHz remote control
n3. Remove/clean :press the learning button about 8 seconds , the indicator turn on to off, it means the information that you keep have been removed successfully .
n
nPackage included:
n
n1/2/3/5/10/20 x 12V 1CH 433MHz Wireless Relay Switch Receiver (optional)
Electronics Ranking
