NI-210 Professional VI Curve Tester Circuit Board Tester Tool With Two-Channel Simultaneous Display
69
Direct purchase from the factory 
Tabbacin Biyan Kuɗi lafiya
Kyauta Kyauta
Manufar Jigilar Kaya
Manufar KomawaKyauta Kyauta
Barka da zuwa Roymall, shafinku na siyan kyaututtuka masu inganci. Muna girmama goyon bayanku, kuma muna ba da kyauta kyauta tare da kowane siyayya. Shirya don bincika tarinmu kuma ku sami kyaututtukanku masu dacewa.Manufar Jigilar Kaya
Za mu aika kayanku cikin kwanaki 2 bayan siyayya.Lokacin jigilar kaya yawanci kwanaki 5-7 ne.Saboda jigilar mu ta duniya ne, lokacin jigilar zai dogara da wurin ku.1. Manufar Komawa
Muna karɓar abubuwan da aka saya daga roymall.com kawai. Ba za a iya mayar da kyauta kyauta ba. Dole ne abu ya kasance ba a yi amfani da shi ba kuma a cikin yanayin da kuka karɓa.Za mu sarrafa komawar ku cikin kwanaki 3-5 bayan karɓa.Ba za a iya mayar da abubuwan da aka keɓance ba.Tuntuɓi mu. service@roymall.com ko Whatsapp: +86193598494712.Manufar Maida Kuɗi
Za ku sami cikakken maida kuɗi bayan mu karɓi abubuwan da aka dawo. Kuɗin jigilar kaya ba za a iya mayar da su ba.Tuntuɓi mu. service@roymall.com ko Whatsapp: +8619359849471
Attention:
It needs to be used with an oscilloscope, and there is no high requirement on the oscilloscope, as long as it is a dual trace oscilloscope. Both analog and digital oscilloscopes can be used (low-end digital oscilloscope xy mode display effect and response speed are a bit worse).
Features:
- Dual-channel signal input
- Two channels display 3 frequencies at the same time
- 5 adjustable voltages: 3V, 10V, 15V, 20V and 60V
- Channel A, channel B, channel A+B display
- With scanning function
- Adjust the position of channel B for easy comparison and measurement
- AC/DC trigger output with adjustable amplitude and width
Summary of the VI Tester:
1. ASA test application characteristics:
Analog Signature Analysis is a fault detection technique widely used in electronic circuit board. Has the following application characteristics:
1.1. It does not involve the circuit principle and does not need the circuit to be in working condition, so it can be used for fault detection of the circuit board without drawings and data, which is out of the equipment (without online testing).
1.2. There is no need to power up the circuit board, which is relatively safer.
1.3. It does not involve the function of the components on the circuit board, so no matter what type of device the circuit is composed of, digital, analog, mixed digital-analog, known functions, unknown (such as dedicated, programmable), etc. can be tested.
1.4. It is tested on a circuit-by-circuit node (device pin), and is basically not limited by the packaging of components on the circuit board. Since a single device can be regarded as the simplest circuit board circuit, ASA technology can also be used to detect the quality of large-scale, complex or integrated devices with unknown functions. In fact, due to limited conditions, ASA is the only way for many users to detect such devices. In addition, when ASA is used to detect the function of discrete components, it is also convenient and intuitive.
2. The basic test principle of ASA:
As far as the basic detection principle is concerned, the ASA test can be seen as a natural extension of the multimeter detection method.
For circuit board without drawings, the most commonly used fault detection method is as follows: first use a multimeter to measure the resistance of the device pins on the circuit board (actually the circuit node) to ground; and then compare it with the corresponding device pins on the failed circuit board. Compare the ground resistance, and judge whether there is a fault on the node according to the difference. From node to specific components need to be manually determined. This method is simple, easy to use and effective. Many people have used this method to repair complex and expensive circuit board.
The main reason for the failure detection rate of this method is that the multimeter can only detect the resistance under 1.5V (multimeter battery voltage), and the ground resistance of the semiconductor device pin changes with the voltage-the resistance under different voltages may not be same. For example, a TTL device pin has a soft breakdown at 2.5V, resulting in a large leakage current. Such failures cannot be detected.
Imagine you have dozens or hundreds of multimeters, and the battery voltage of each meter is different-the voltage range includes the working voltage of the device. For each pin, use these tables to test and compare all of them, so that the above-mentioned faults will be detected. This is the principle of ASA testingu2014comparison in a voltage range, not just at a voltage point.
Package Included:
1 x Set of IV Curve Tester
Note:
- Battery is not included.
It needs to be used with an oscilloscope, and there is no high requirement on the oscilloscope, as long as it is a dual trace oscilloscope. Both analog and digital oscilloscopes can be used (low-end digital oscilloscope xy mode display effect and response speed are a bit worse).
Features:
- Dual-channel signal input
- Two channels display 3 frequencies at the same time
- 5 adjustable voltages: 3V, 10V, 15V, 20V and 60V
- Channel A, channel B, channel A+B display
- With scanning function
- Adjust the position of channel B for easy comparison and measurement
- AC/DC trigger output with adjustable amplitude and width
Summary of the VI Tester:
1. ASA test application characteristics:
Analog Signature Analysis is a fault detection technique widely used in electronic circuit board. Has the following application characteristics:
1.1. It does not involve the circuit principle and does not need the circuit to be in working condition, so it can be used for fault detection of the circuit board without drawings and data, which is out of the equipment (without online testing).
1.2. There is no need to power up the circuit board, which is relatively safer.
1.3. It does not involve the function of the components on the circuit board, so no matter what type of device the circuit is composed of, digital, analog, mixed digital-analog, known functions, unknown (such as dedicated, programmable), etc. can be tested.
1.4. It is tested on a circuit-by-circuit node (device pin), and is basically not limited by the packaging of components on the circuit board. Since a single device can be regarded as the simplest circuit board circuit, ASA technology can also be used to detect the quality of large-scale, complex or integrated devices with unknown functions. In fact, due to limited conditions, ASA is the only way for many users to detect such devices. In addition, when ASA is used to detect the function of discrete components, it is also convenient and intuitive.
2. The basic test principle of ASA:
As far as the basic detection principle is concerned, the ASA test can be seen as a natural extension of the multimeter detection method.
For circuit board without drawings, the most commonly used fault detection method is as follows: first use a multimeter to measure the resistance of the device pins on the circuit board (actually the circuit node) to ground; and then compare it with the corresponding device pins on the failed circuit board. Compare the ground resistance, and judge whether there is a fault on the node according to the difference. From node to specific components need to be manually determined. This method is simple, easy to use and effective. Many people have used this method to repair complex and expensive circuit board.
The main reason for the failure detection rate of this method is that the multimeter can only detect the resistance under 1.5V (multimeter battery voltage), and the ground resistance of the semiconductor device pin changes with the voltage-the resistance under different voltages may not be same. For example, a TTL device pin has a soft breakdown at 2.5V, resulting in a large leakage current. Such failures cannot be detected.
Imagine you have dozens or hundreds of multimeters, and the battery voltage of each meter is different-the voltage range includes the working voltage of the device. For each pin, use these tables to test and compare all of them, so that the above-mentioned faults will be detected. This is the principle of ASA testingu2014comparison in a voltage range, not just at a voltage point.
Package Included:
1 x Set of IV Curve Tester
Note:
- Battery is not included.
